Worm get gearbox with motor
A robust worm-travel gearbox powered by an MM28 electric motor. Ideal applications where a simple to match, high torque outcome is required. Ideal for student based assignments which includes robots and buggies.
The unit has been designed so that the output shaft can be ‘clicked’ in and out for modification. E.g. cutting down to size. The engine is snap installed into its cradle to activate the gear and worm.
1 – 6V DC
0.1A to 1A depending on load
Driveshaft length: 12.5cm
Driveshaft diameter 3mm
Gearbox ratio: 42:1
Overall dimensions of box + electric motor: 35(W) x 40(H) x 60(L)mm
The primary feature of the high-efficiency gear box is a worm gear, which locks the output shaft whenever the motor is not turning. The high gear ratios of 216:1 or 336:1 make this gearbox appropriate for little strolling robots, lifting mechanisms, and additional applications where high torque is desired.
The low-voltage motors in the worm gearbox operate on 1.5-4.5 volts and draft to some amps, making them perfect applicants for the DRV8833 motor driver carrier. Engine overheating can be due to excessive stalling, actually at suprisingly low voltages. We advise that you utilize stall-detection sensors, or simply watch your robot, to ensure that it doesn’t stall for more than a few seconds at the same time.
This gearbox has a 4 mm diameter, round output shaft, which works with the wheels that are compatible with Tamiya 4 mm, round shafts. Our 3 mm universal installation hub also fits on the smaller threaded end of the shaft, though it is not specifically intended to work with this type of shaft (the hub’s set screw could damage the thread on the shaft).
Ever-Power gear motors happen to be economical, right-angle, worm-geared motors that install easily found in the tightest applications. Economical right angle worm geared motors established new standards for reliability, effectiveness and economic climate with unparalleled features which includes hollow shafts in the tiniest sizes. An inverter friendly design provides for easy integration now and a really future proof answer. The Ever-Power gear motor offers total versatility in mounting options includes shaft, base, encounter, and flange alternatives. The engine terminal box could be mounted in choice positions rotated in 90º steps around the motor frame offering for unparalleled integration options.
Ever-Power gear motors adhere to UNITED STATES and International criteria, including NEMA, IEC, CSA, and CE, the Ever-Power series allows for worldwide acceptance, a genuine total solution for our global customers.
Excellent protection of IP65 acc. to IEC 529 assures you that the Ever-Power series is dirt tight and hose evidence,and can be used outdoors or in wet and dusty environments without the use of additional enclosures. Full rated output is available at the result shaft of the unit.
Power ranking up to 5,5 kW.
Torque 25 … 1.000 Nm
Output Speeds 0,2 … 300 min-1
versatile installation possibilities
Totally enclosed, sealed against dust and water spray
Lubrication change initial after 15000 hrs
Low noise gearing
Mains connection 110 … 690V, 50/60Hz
Enclosure IP65 (Standard), IP66 (Optional)
Connecting with Plug connectors.
With built-in inverter up to 7,5kW.
CSA, UL, ATEX, GOST, CCC, ISO9001, ISO14001, OHSAS18001
Motors according to EN 60034
Corrosion category predicated on DIN ISO 12944-5
C1, C2, C3, C4, C5-We, C5-M
DC WORM GEAR MOTORS
Ever-Power DC worm equipment motors are the remedy for applications requiring a corner turn, optional dual result, or an inability for the motor to be back again driven. The DC correct angle gear motors are created for continuous and intermittent duty procedure. Our right angle gear reducers were created with many mounting plate options, making them well suited for a variety of DC motor based applications. We offer 12 ratios which range from 5:1 to 100:1.
1/43 to 3/8 HP
12, 24, 90, 130, 180 VDC, 115 FWR
9 – 475 RPM
1.5 – 315.9 in-lb rated torque
Frame Size 60, 80, 108 mm
5:1 – 100:1 standard ratios
Standard brush life of 2000+ hours (varies by application)
EP Products Worm Gear Motors are made to generate high torque in a little package size. Worm Equipment Motors are great for applications that want a personal- locking or breaking characteristic since the result shaft can’t rotate when there’s no power applied. Also, Worm Gearheads can transfer movement in 90 degrees. With various decrease ratios, precision trim gears, voltages and sizes, EP Products has a DC Worm Equipment Motor solution for the application.
Features and Benefits
Very High Torque Capabilities
Self-Locking / Braking Features
Motion Transfer of 90 Degrees
Capability to Handle Large Equipment Reduction Ratios
Security Door Locks / Industrial Conveying Devices / Security Gates / Dental care Seats / Ambulance Cots & Stretchers Quite a few DC Motors could be complimented with among our Worm Gearheads. EP Products will work with you to design and produce a Worm Gear Motor that will optimize the efficiency of your unique application.
Built to your unique requirements
Engine Type: Brushed / Brushless / Coreless
Shaft Material & Size
Shaft Configuration: (D Chop / Round / Splined / Other)
Overall Size Parameters (L, W, H)
Encoder Type: Optical / Hall Effect
Additional Assembly Requirements (lead wires, connectors, etc.)
The turbo metal gear worm electric motor uses a metal gear box for toughness and a higher torque output. Due to the special mechanical framework of the worm get the electric motor output shaft is definitely self locking and will not be rotated.
This part uses a two wire connection and supports direction control as well as PWM speed control. Ranked voltage is 12v and can achieve 40RPM, with a torque of 8kg/cm.
Operating Voltage: 6 – 15 V
Rated Voltage: 12V
No-load Speed: 40 RPM
No-load Current: 35 mA
Rated Torque: 32 RPM
Rated Current: 180 mA
Ranked Torque: 2.2 kg.cm
Rated Power: 1.1 W
Stall Torque: 8 kg/cm
Stall Current: 1 A
Reduction Ratio: 1:150
Weight: 167 g
EP Geared Motors with Worm Gearing – Modual & Customizable drive technology
Worm gear units from EP DRIVESYSTEMS especially display their strength in applications where large gear ratios are essential. Our worm geared motors will be as a result optimally suited for make use of in intralogistics, packaging technology and the meals & beverage industry.
Four great known reasons for EP worm geared motors:
Our worm geared motors have a higher overload capacity
Washdown versions allow simple and effective cleaning of the drive system.
The NSD tupH sealed surface area conversion is exceptionally chemical, corrosion and abrasion resistant.
Our modular design give users optimum freedom.
The modular system for optimum flexibility: Our EP worm gear units
There are many applications that require drive systems, and each one of these has its own unique requirements. The EP series worm gear motors can be quickly and effectively adapted to satisfy your needs.
Worm gear units impress with their large power density and compact style. If required, we are able to also source them with the impressive nsd tupH surface area treatment.
In addition to the basic EP casing, you can expect an extensive line of bolt-on parts to customize the merchandise including torque arms, shaft addresses and output flanges. These could be easily field set up, but we may also be glad to assemble the average person components for you.
Find out more about our modular SI worm geared motors!
Find out more
Smooth and Tidy: The EP worm equipment unit SMI
SMI worm gear systems feature a simple, corrosion-resistant alluminum alloy casing. Optional nsd tupH surface area conversion makes this product preferably suited for severe and demanding industries like food processing and pharmaceuticals.
Flexible input designs such as NEMA, IEC or direct motor mounts in extra foot or flange mounted housing designs.
Worm geared motors
Worm geared motors for little power range.
The WATT small worm gear unit adapt themselves concerning UNIBLOCK design optimally in the geared engine program. The units have got on all sides numerous repairing possibilities and enable a simple assembling for the client.
Various other drive configurationscan be created by use of built-on accessories (e.g. torque arm and output flanges). The housings are made in light weight construction out of aluminium die cast. Engine attachment is realised generally through IEC adapter B5 or B14A.
Number of sizes:5
Power Range:0.12 – 2.2kW
Output torque range:17 – 230Nm
Ratio:5 – 100
Output option:output shaft, output shaft on both sides, hollow shaft, hollow shaft with shrink disc
Assembly/mounting:uniblock, flange, torque arm
Buy Worm Get Gearbox with Engine – incorporating the following features: 1 to 6V voltage rating, 17100 rpm no load speed, 220g-cm stall torque, 3mm shaft size, 60mm long, 35mm vast, 40mm high, a robust worm drive gearbox powered by an MM28 electric motor (included), most ideal for applications where a simple to fit, high torque outcome is necessary, nylon housing and equipment, requires light oil or silicon grease lubrication, well suited for student based tasks including robots and buggies.
Most ideal for applications where a simple to fit, high torque productivity is required
Ideal for student based tasks including robots and buggies
Reversible Substantial torque Turbo Worm Gear Motor JGY370 DC 12V 40RPM
Reversible High torque Turbo Worm Gear Electric motor JGY370 DC 12V 40RPM
The motor is Gear DC motor with micro-turbine worm, you can transform the wiring-connection to change motor rotation.
Turbo worm geared engine with self-lock, that is, in the case of motor without electrical, the end result axis is fixed, self-lock.
The reducer output shaft arranged vertically with the engine shaft, whole electric motor output shaft relatively-short than general gear motor, trusted to be installed the dimensions requirements strictly occasion.
No load speed: 40r/min
Result torque: 5.6kg.cm
Rated current: 0.06A
Application: open the home window, door, Mini winch. Ect.
In sumo robot or combat robot competition where great holding torque’s motor is essential to avoid your robot being pushed by your opponent robot. The worm gear is definitely an improved option compared to the spur gear motor. Why is worm gear so unique? Check this wiki out: Worm Travel.
“Unlike with ordinary equipment trains, the path of transmission (insight shaft vs result shaft) is not reversible when working with large reduction ratios, because of the increased friction involved between your worm and worm-wheel, when usually an individual start (1 spiral) worm can be used. This is often a advantage when it is desired to remove any likelihood of the result driving the input.”
In other words, it is hard to push your load (example, your robot) if the motor is not power or rotate.
Features and Spec:
Metal gear box
Output shaft is self-locking due to the worm gear’s characteristic
Rated voltage: 12V DC
Rated output speed: 150 RPM
Rated output torque: 117mN.m (1.2kgf.cm)
Stalled torque: 196mN.m (2kgf.cm)
No load current: 60mA
Stalled current: 1.8A
Output shaft diameter: 6mm with 4.5mm slot
worm motor, the best selection for you.